 |
Cutter
CU4
With the cutter labels, cardboards, textiles and heat shrink
tubes are cut separately, as multiple printed panels or at
the end of the print job. |
|
|
|
 |
Perforation cutter PCU4
With the perforation cutter labels, cardboards, textiles and
heat shrink tubes are perforated and cut separately, as
multiple printed panels or at the end of the print job.
Perforation cutter PCU4/2,5, perforation distance 2.5 mm
Perforation cutter PCU4/10, perforation distance 10 mm
|
|
|
|
 |
Stacker
with cutter
The printed materials are cut and piled up with the stacker.
The print job stops when the height of the pile is reached.
To keep the bending of the material during piling as small
as possible cab recommends a broad core diameter.
The storage table and the protective cover are adjusted to
the label size and have to be ordered separately.
With the base frame the devices can be arranged on the table
in any order.
|
|
|
|
 |
Rewind
guide plate for internal rewinding- for label rolls up to
145mm Ø
The internal rewinding is operated with the dispense printer
(P-version). For the printers A2+ and A4+ the peel-off plate
is replaced by a rewind guide plate.
|
|
|
|
 |
External
rewinder ER1/2/3 - for direct connection onto the printer
The rewinder is bolted directly onto the printer. The label
winding is optionally inside or outside. The electronic
control via the swing arm provides a smooth and tight
winding
|
|
|
|
 |
External
Rewinder ER 4/6/8 - with built-in power supply
The rewinder can be attached to almost every other printer.
All other technical data are according to the rewinder.
|
|
|
|
 |
External
Unwinder EU 4/6/8
It enables a smooth feeding of labels for heavy rolls. The
unwinder works both with inside and outside wound labels.
|
|
|
|
 |
Tester
for linear barcodes
The built-in scanner tests the barcode directly after
printing. If the barcode is not readable the printing
process can be stopped at once so the faulty labels can be
removed. It is primarily intended to be used with the
external rewinder ER4 - ER8.
|
|
|
|
 |
Accessories for dispensing of labels - automatically or on
demand
Dispensing labels requires an additional present sensor or
peel-off adapter. cab offers devices both for manual
operation and automatic operation.
|
|
|
|
 |
Present
sensor PS 8 - for manual operation
The photo cell detects the label in peeling position and
pauses the labeling process. After removing the label
manually the next one is printed instantly.
|
|
|
|
 |
Present
sensor PS 5- for automatic operation
Dispensing labels requires an additional present sensor or
peel-off adapter. cab offers devices both for manual
operation and automatic operation.
If labels are difficult to remove from the liner a peel-off
plate with rewind guide plate, extended by 10 mm, is used.
|
|
|
|
 |
Present
sensor PS 6 - for manual and automatic operation
1. As with PS 8 after removing the label the next one is
printed automatically.
2. Dispensing on demand with present trigger, foot switch or
an external signal (according PS 5)
|
|
|
|
 |
Present
sensor PS 9 - for manual and automatic operation
For dispensing labels where the front edge is not detected
by the present sensor PS 6. The extension is made on
customer-specific.
|
|
|
|
 |
Pause
adapter PS 7 - for basic and dispense devices
The print job is stopped with the pause signal. The active
label is finished, e.g. by using a label loop.
Inputs: Pause, external error
Outputs: No print job, printer not ready, print job active
|
|
|
|
 |
Present
trigger
Starts printing and dispensing.
|
|
|
|
 |
Foot
switch
Starts printing and dispensing.
|
|
|
|
 |
Sub-D
plug
Connection of the external control signals for automatic
operation. Sub-D plug 15-pole with screw clamps.
|
|
|
|
 |
External
panel
If the panel is not accessible anymore, e.g. after
installation within a facility, it is possible to install an
external panel. Additionally there is a slot for a CF memory
card Type 1 and a USB Master interface. |
